Route A→B
Click a start and an end, and get conduit that keeps clear of what’s in the way.
Pick two devices or conduit ends and get a conduit route with real elbows that keeps clear of everything set to Avoid. You see the real route before it stays in the model, change what you dislike, and add it in one click.
Overview
Clear of what to avoid
Every route is checked against the model’s real geometry before you accept it, and what it passes through is listed.
Review before it stays
The suggestion is shown for review first; Cancel discards it and leaves the model as it was.
One undo step
Add conduit keeps the route as one undo step, and Add and route next starts the next route from where you ended.
Watch: Route A→B
Pick a start and an end. Pembris finds a route around what to avoid and shows it for review.
What it supports
Each capability and its status today. Planned items are on the roadmap, not yet built.
- Supported
- Partial
- Planned
- Not supported
Routing
- Supported
Between two devices or conduit ends
An open end of an existing run can start or end a route; the new conduit joins it.
- Supported
Up to three different suggestions
Step through them with Previous and Next.
- Supported
Real elbows and straight runs
Planned with the measured size of your project’s elbows.
- Supported
Bend limit per run
360° between pull points unless you change it, with Warn, Confirm, Refuse or Off over it.
- Supported
Devices without a conduit connector
The conduit ends at the device and the review marks that end Not joined.
- Partial
Two to four conduits side by side
Only between two devices with enough free openings facing one way, and not with a common height or chosen openings.
Review and change
- Supported
Change openings
Choose the exact opening at either end, for this route only.
- Supported
Change layout, conduit and fittings
Direction, height, conduit type and size, for this route only.
- Supported
One-click fixes when it refuses
Such as Show in view, Search further, Reduce clearance or Route through this kind, this time.
- Supported
Route several pairs in a row
Add and route next (Ctrl+Enter) offers the last end as the next start.
- Supported
Plan wires after Add
Offered as a separate undo step; a failed wire keeps the conduit.
- Not supported
Change the model from the review
The review only selects, refreshes and zooms. Only Add keeps anything.
Next, and what it won’t do
- Planned
Routing styles
Follow structure or run beside other services, with today’s shortest route kept as the default.
- Planned
Pull boxes past the bend limit
A reachable pull box proposed in the review.
- Planned
Offsets and 45° bends
Where a pair of 90° bends wastes length or bend.
- Not supported
Save a this-route choice to your settings
Direction, height and refusal fixes apply to one command only.
Compatibility
- Revit 2025Supported
Autodesk Revit 2025 on Windows.
- Revit 2026Supported
Autodesk Revit 2026 on Windows.
- Linked modelsSupported
Elements in loaded links are kept clear of and never changed. An unloaded link stops routing until you reload it or choose Ignore this link.
- MagiCAD contentPartial
MagiCAD families work like any other Revit family; there is no MagiCAD-specific handling.
- Conduit drawn by handSupported
Start from or end at an open end of an existing run; the route keeps that run’s type and size.
Settings
Where to change how it behaves.
- My settings › Routing › Bends
- The bend limit per run (360° by default) and what happens over it: Warn, Confirm, Refuse or Off.
- My settings › Routing
- Conduit type and size, clearance (25 mm by default), direction, minimum straight run and Keep routing.
- My settings › Obstacles
- What routes Avoid and what they may Go through, by category, family or type.
- My settings › This PC › Performance
- Search harder: how long one search may take, from 1 to 20 seconds (5 s by default).
Guides for Route A→B
- What is Pembris Electrical?Pembris Electrical is a Revit add-in by Pembris AS that draws, checks and counts conduit work for electricians and electrical designers.
- A tour of the ribbon and side paneWhere everything is: the Pembris Electrical ribbon tab, its panels, and the side pane that docks beside Properties.
- Route your first conduitA short walkthrough: pick two devices, review the suggested route and add the conduit as one undo step.
- Keyboard shortcutsThe keys that work in the route review, the side pane, Check routes and while placing devices.
- Route A→BPick a start and an end, and Route A→B draws a checked conduit route with elbows that keeps clear of everything set to Avoid.
- Choose start and end pointsWhat Route A→B can start and end at, and how it chooses the opening at each end.
- Review a suggested routeRead the Route A→B review: the ends, what the route passes through, warnings, and the buttons that add, change or cancel it.
- Change openings, layout and conduitUse More in the review to choose the openings, direction, height, side-by-side conduits, conduit type and size for one route.