Check routes
See which routes still meet their devices, and fix the ones that don’t.
Look over the routes in the view or selection after the model has changed or someone edited by hand. See which still meet their devices or now clash, find the damage in the view, and fix it in one click and one undo step.
Overview
Problems first
Routes are grouped Needs a look, Notes and Other routes, and F8 steps to the next one that needs a look.
Damage in red
Show fades the route and draws what is wrong in red, without changing the model.
Checks while you work
It checks a few routes at a time, so you can pan, select and edit meanwhile, and Stop keeps what was checked.
What it supports
Each capability and its status today. Planned items are on the roadmap, not yet built.
- Supported
- Partial
- Planned
- Not supported
What it checks
- Supported
Clashes and too close
Against Avoid obstacles near the route, within your clearance.
- Supported
Ends that moved, came loose or were deleted
A device that only moved is no finding; whether the route still meets it is.
- Supported
Too many bends and missing fittings
- Supported
Zone rules
Breaking a zone rule, or leaving a preferred zone.
- Partial
Conduit Pembris didn’t draw
Listed as By hand and checked only: Show, Select, Open in 3D and Copy list.
- Partial
Up to 100 routes at a time
Check next routes takes the next 100.
Fixes
- Supported
Re-route
Plans again between the same devices and replaces the route after the normal review.
- Supported
Record ends and Adopt copies
Accept changed ends, or make a pasted copy a route of its own.
- Supported
Copy › Here or To clipboard
One route at a time, optionally with the devices it connects.
- Supported
Remove
Deletes ticked routes in one undo step after asking.
- Supported
Run data
Schedule columns for each physical run: bends, elbows, installed length and ends.
- Not supported
Fix or re-route conduit Pembris didn’t draw
That would need its own setting and approval.
- Not supported
Move devices or change linked models
Compatibility
- Revit 2025Supported
Autodesk Revit 2025 on Windows.
- Revit 2026Supported
Autodesk Revit 2026 on Windows.
- Linked modelsPartial
Routes ending at a tray in a loaded link are checked; conduit inside links isn’t read.
- MagiCAD contentPartial
MagiCAD families work like any other Revit family; there is no MagiCAD-specific handling.
- Conduit drawn by handPartial
Listed and checked only; no fixes.
Settings
Where to change how it behaves.
- My settings › Checks
- Which checks run (clashes, clearance, device changes, bends, zones) and the move, angle and end-gap tolerances.
- My settings › Appearance
- The highlight and problem colours, movement and line weight.
- My settings › Routing › Bends
- The bend limit that Too many bends is counted against.
Guides for Check routes
- A tour of the ribbon and side paneWhere everything is: the Pembris Electrical ribbon tab, its panels, and the side pane that docks beside Properties.
- Keyboard shortcutsThe keys that work in the route review, the side pane, Check routes and while placing devices.
- Bend limits and pull pointsEach run keeps within your bend limit between pull points, 360° unless you change it, and you choose what happens when it can’t.
- Check routesCheck routes lists the routes in your selection or view, checks them while you keep working and shows what needs a look.
- Fix a finding: Re-route, Record ends and AdoptChoose the right fix for a finding in Check routes, for one route or several, each in one undo step.
- Conduit drawn by handCheck routes and Check project list and check conduit Pembris Electrical didn’t draw, but never change it.
- Run data in schedulesAdd six run data columns to a project so a normal Revit schedule shows one row per physical run, with its length and bends.
- Record endsEvery route remembers what it connects; Record ends accepts a moved or turned device and adds split or hand-drawn parts to the route.