Check project
Every route in the project checked before you issue the model.
Check every route in the project before a model is issued or sent to coordination, including conduit Pembris didn’t draw. You get a short list of what’s wrong, a one-click fix where there is one, and a list to hand on.
Overview
Counts by kind
Clashes, runs over the bend limit, missing fittings, unjoined ends and anything that couldn’t be checked.
An honest pass
It says every route passes only when every route and run was checked in full.
A list to hand on
More › Copy list puts the routes shown on the clipboard, ready to paste into a spreadsheet.
Watch: Check project
Count every problem before issue, then fix routes with Re-route.
What it supports
Each capability and its status today. Planned items are on the roadmap, not yet built.
- Supported
- Partial
- Planned
- Not supported
What it checks
- Supported
Every route in the project
Whatever the view shows; up to 500 at a time, then Check next routes.
- Supported
Clashes, bends, missing fittings and unjoined ends
- Partial
Conduit Pembris didn’t draw
Checked and counted in the same filters, but never fixed.
- Partial
Estimated tray landing load
Only with the opt-in project tray capacity, and an estimate, not cable fill.
- Not supported
Part of a project passed off as the whole
Over 20,000 route elements or conduits, or a closed workset, refuses and checks nothing.
- Not supported
A certificate for the whole model
It checks conduit routes, nothing else.
Fixes
- Supported
Filter by kind of problem
Each active filter shows as a chip that removes it.
- Supported
Re-route where it helps
Not on unjoined ends, where Revit would refuse the same join again.
- Supported
Copy list
One row per route, tab-separated.
- Not supported
Fix conduit Pembris didn’t draw
Only Show, Select and Copy list.
Next
- Planned
Findings that say what may not comply
Citing the clause of the project’s code; the installer decides.
- Planned
An advisory report as PDF and CSV
Never a declaration of conformity.
- Planned
Fill and segregation
Conduit and tray fill, and power kept apart from data and other services.
- Planned
Fire penetrations
Every fire-rated wall or floor a route passes, listed for the firestop contractor.
Compatibility
- Revit 2025Supported
Autodesk Revit 2025 on Windows.
- Revit 2026Supported
Autodesk Revit 2026 on Windows.
- Linked modelsPartial
Checks the host model’s routes and conduit; linked models aren’t read.
- MagiCAD contentPartial
MagiCAD families work like any other Revit family; there is no MagiCAD-specific handling.
- Conduit drawn by handPartial
Checked and counted, and a problem stops the pass, but it gets no fix.
Settings
Where to change how it behaves.
- My settings › Checks
- Which checks run and their tolerances. Missing fittings and unjoined ends are always checked.
- My settings › Routing › Bends
- The bend limit runs are counted against (360° by default).
- Change drop options › Project tray capacity…
- Turns on the tray landing load report for this project.
Guides for Check project
- What is Pembris Electrical?Pembris Electrical is a Revit add-in by Pembris AS that draws, checks and counts conduit work for electricians and electrical designers.
- Tray capacity and project targetsTurn on an estimate of how much conduit lands on each tray section, with a project target and reserve that guide Drop to tray.
- Check project before you issueCheck project checks every route and conduit run in the project and counts what is wrong before you issue the model.
- Conduit drawn by handCheck routes and Check project list and check conduit Pembris Electrical didn’t draw, but never change it.
- Check routesCheck routes lists the routes in your selection or view, checks them while you keep working and shows what needs a look.
- Fix a finding: Re-route, Record ends and AdoptChoose the right fix for a finding in Check routes, for one route or several, each in one undo step.
- Re-routeRe-route plans a route again between its recorded devices and replaces it after you review the new one.
- Route watchRoute watch notices when an edit affects a route, tells you without interrupting, and fixes routes only if you choose that.