Drop to tray
Every selected device gets its own drop to the nearest cable tray.
Run conduit from devices to cable trays without drawing every drop by hand. Change the device list, let it choose the tray or pick one, and keep the drops that work even when some devices can’t reach.
Overview
Many devices at once
One review and one undo step for the whole batch, with no fixed limit on the number of devices.
Automatic or chosen tray
It tries the nearest trays, or only the one you pick. The tray itself is never changed.
Keeps what works
Add N of M drops keeps the reachable ones and leaves the devices that failed selected.
Watch: Drop to tray
Each selected device gets its own drop to the nearest cable tray.
What it supports
Each capability and its status today. Planned items are on the roadmap, not yet built.
- Supported
- Partial
- Planned
- Not supported
Devices and trays
- Supported
Edit the device list
Start from the selection, or add devices in the view that have no route yet.
- Supported
Trays in this model and in loaded links
Angled, sloped, vertical and rotated-link trays included.
- Supported
Bottom, side or top entry
Bottom and side are on by default; top is optional.
- Supported
Reach from 500 to 30,000 mm
10 m by default.
- Not supported
Change the tray or move devices
Drops end at the tray, and tray ends stay deliberately unjoined.
Drop content
- Supported
Rigid conduit
Uses the device sizes and the project’s conduit catalogue.
- Supported
ABB Adaptaflex SN20, SN25 and SN32 flexible drops
Generated fittings with real connectors, catalogue diameters and bend radii.
- Partial
Cablofil clamps
Only with verified clamps per size already in the project; missing or changed content sends you to Drop options.
- Supported
Re-route a drop
Keeps its tray, conduit type, size, flexible product and clamp.
Tray landing load
- Partial
Estimated landing load
Opt-in per project. An estimate over nominal tray width × height, not cable fill.
- Not supported
Cable fill or compliance
External and through cables and downstream sections aren’t counted, so it can’t say a tray complies.
- Planned
Conduit and tray fill
From cable outside diameters against a verified limit.
Compatibility
- Revit 2025Supported
Autodesk Revit 2025 on Windows.
- Revit 2026Supported
Autodesk Revit 2026 on Windows.
- Linked modelsSupported
Drops to trays in loaded links. The landing-load estimate leaves drops in linked models out.
- MagiCAD contentPartial
MagiCAD families work like any other Revit family; there is no MagiCAD-specific handling.
- Conduit drawn by handSupported
Existing conduit is kept clear of; runs and fittings in the selection are left out of the list.
Settings
Where to change how it behaves.
- My settings › Routing
- How far Drop to tray looks for a tray (10 m by default) and which tray faces a drop may enter.
- My settings › This PC › Performance
- How many trays one drop tries (4 by default, up to 16) and the extra memory it may use.
- Drop to tray › More › Change drop options
- Rigid or flexible content, reach and clamps, remembered for this document until Revit closes.
- Change drop options › Project tray capacity…
- Landing load target (40 %) and reserve (20 % of it), saved in the project. Off unless you turn it on.
Guides for Drop to tray
- What is Pembris Electrical?Pembris Electrical is a Revit add-in by Pembris AS that draws, checks and counts conduit work for electricians and electrical designers.
- Drop to trayGive each selected device its own conduit drop to the nearest cable tray, or one you pick, and add the reviewed drops as one undo step.
- Flexible drops and tray clampsChoose rigid conduit or an ABB Adaptaflex flexible drop, and optional Cablofil clamps at the tray, in Drop options.
- Tray capacity and project targetsTurn on an estimate of how much conduit lands on each tray section, with a project target and reserve that guide Drop to tray.
- Linked modelsHow routes, tray drops and devices treat linked models, and what happens when a link is unloaded.
- Connect devicesPlan conduit between several devices as one network, review it and add it as one undo step.
- Connect a circuit and its panelAdd a circuit’s devices and its panel to Connect devices in one step, then route them as one network.
- Chain or tree?How Connect devices links devices as a chain or a tree, and how the start device, openings and height shape the network.