Circuits
Each board’s circuits with their longest cable length, ready for the kursfortegnelse.
Go to a board in the side pane, see its circuits with each one’s longest cable length, mark them on the drawing and export the kursfortegnelse as Excel, CSV or PDF. Where MagiCAD has calculated a project, its own circuit data is used, voltage drop and Ik min included.
Overview
Longest cable length
Measured along joined conduit and tray, rounded up, with ~ where part of it is planned or estimated.
Kursfortegnelse export
Excel, CSV or a printable A4 PDF, for one board or every board at once.
Normal Revit circuits
New circuit makes ordinary Revit circuits, so schedules, tags and MagiCAD still work.
Watch: Circuits
See each circuit’s longest cable length and write labels on the plan.
What it supports
Each capability and its status today. Planned items are on the roadmap, not yet built.
- Supported
- Partial
- Planned
- Not supported
Boards and circuits
- Supported
Boards listed, Needs a look first
Each row says its level, so boards with the same name are told apart.
- Supported
New circuit by name
Click its devices then or later.
- Supported
Add, rename and remove boards
Rename and remove only on Pembris’s own boards.
- Supported
Numbering…
Where a board’s numbers start and which places stay free, stored on the board as Revit does.
- Supported
Change number…
Swap with the circuit that has the number, or replace one New circuit made.
- Supported
Circuit table
Every board’s circuits in one window you can put on a second monitor.
Lengths, labels and export
- Supported
Longest length per circuit
Board tail and slack per device included, rounded up, never down.
- Partial
Planned stretches
Where no conduit is drawn, it plans via the ceiling or in the wall and marks the length with ~.
- Supported
Labels on the drawing
Text such as "U1-3", or a circuit tag, as one undo step per board.
- Supported
Export as Excel, CSV or PDF
Or Copy the columns as tab-separated text.
- Not supported
Read linked models
Circuits and conduit in links aren’t read.
MagiCAD
- Partial
MagiCAD circuit numbers and figures
Read wherever MagiCAD has calculated the circuit.
- Supported
Voltage drop and Ik min checks
From MagiCAD’s own figures: voltage drop over 4 %, or Ik min too low for a B, C or D breaker.
- Not supported
Change MagiCAD’s values
Circuits never writes them or works out its own voltage drop.
Compatibility
- Revit 2025Supported
Autodesk Revit 2025 on Windows.
- Revit 2026Supported
Autodesk Revit 2026 on Windows.
- Linked modelsNot supported
Circuits and conduit in linked models aren’t read.
- MagiCAD contentPartial
Uses MagiCAD’s circuit numbers, voltage drop and Ik min wherever MagiCAD has calculated them.
- Conduit drawn by handSupported
Lengths follow joined conduit and tray, whoever drew them.
Settings
Where to change how it behaves.
- Circuits › Preferences… (lengths)
- Via the ceiling or in the wall, cable height (2400 mm), board tail (1500 mm), slack per device (300 mm) and rounding (500 mm).
- Circuits › Preferences… (labels and reports)
- Text, Auto or Tag labels, label format, language, decimal comma and report columns.
- Circuits › Circuit setup…
- Use my Revit setup, or Let Pembris fill in the setup, for New circuit in this project.
Guides for Circuits
- Connect a circuit and its panelAdd a circuit’s devices and its panel to Connect devices in one step, then route them as one network.
- Circuits in the side paneCircuits lists every board’s circuits with their longest cable lengths, ready to label on the plan and export as a kursfortegnelse.
- How longest cable lengths are measuredCircuits follows the conduit and cable tray drawn in the model from the board to each device, plans what isn’t drawn and always rounds up.
- Add boards and circuitsAdd a board at any sikringsskap, then make each circuit by name with New circuit and click its devices now or later.
- Numbering and Change numberSet where a board’s circuit numbers start, keep reserves free for later circuits, and give any circuit another number.
- Circuit labels on the planLabels writes each device’s board and circuit number, such as U1-3, in the active plan, section or elevation, in one undo step per board.
- Export circuit reportsExport one board, ticked boards or every board as Excel, CSV or a printable PDF kursfortegnelse, with MagiCAD’s voltage drop and Ik min checked where it has calculated.
- The circuit tableThe circuit table shows every board’s circuits in one window you can put on a second monitor, follows your changes and renames or adds circuits in place.